E1.20 RDM (Remote Device Management) Protocol Forums  

Go Back   E1.20 RDM (Remote Device Management) Protocol Forums > RDM Developer Forums > RDM Interpretation Questions

RDM Interpretation Questions Discussion and questions relating to interpreting and understanding the E1.20 RDM Standard.

Reply
 
Thread Tools Search this Thread Display Modes
Old October 4th, 2010   #1
CyrilU
Junior Member
 
Join Date: Oct 2010
Posts: 3
Default RDM discovery trouble

Hello to all,

I try to make a responder for my fixture.
All is good with on responder but
when i put more than one responder the discovery process
is having some trouble.

the serial number of my 3 fixture are :
4179-00006E34/4179-00006EAD/4179-00006EB2.

I test with on "ELC checker" sender : the trouble is that this sender
detect my 3 serials and some more like 4179-00006EBC or
4179-00006E3D ...
I test also with an other sender "TBox RDM" : the trouble is that in the most case, the discovery process never end.

I have read some post in this forum discussing about a similar problem.
Is there already an issue for that type of trouble ?

thanks for your help

Cyril
CyrilU is offline   Reply With Quote
Old October 4th, 2010   #2
ericthegeek
Task Group Member
 
Join Date: Aug 2008
Posts: 380
Default

It sounds like you are running into the phantom device problem. There are several things that can cause this to occur:

Responder Firmware Errors:
Make sure that your firmware is correctly handling the upper and lower bounds for the DISC_UNIQUE_BRANCH message. An off-by-one error where your device responds when it shouldn't (or doesn't respond when it should) can appear as a phantom device. A common mistake is to use less-than/greater than comparisons rather than less-than-equal-to/greater-than-equal-to.

I don't think this is what's happening to you. Typically this results in a phantom device with the last digit being one more or one less than the real responder's UID.


Collisions During the Discovery Response:
During the 5.8ms discovery response period, it's common to get collisions on the DMX wire when multiple responders reply simultaneously. Sometimes these collisions can appear to have a valid checksum. A properly written controller will attempt to mute the phantom device, get no response, and continue further down the binary tree.

However, some RDM controllers do this wrong, and add the phantom device to the Table of Devices even if the device does not respond to the DISC_MUTE message. This is a common bug in RDM controller software, and I suspect this is what is happening to you. You'll need to contact them and ask how their discovery routine works. Better RDM controllers will not have this problem.

I have not used an "ELC checker" or the "TBox RDM" so I can't tell you how they behave. To know for sure what's happening you'll need an RDM packet analyzer.
ericthegeek is offline   Reply With Quote
Old October 11th, 2010   #3
ericthegeek
Task Group Member
 
Join Date: Aug 2008
Posts: 380
Default

Cyril, have you made any progress on this?
ericthegeek is offline   Reply With Quote
Old October 22nd, 2010   #4
CyrilU
Junior Member
 
Join Date: Oct 2010
Posts: 3
Default

No, i have contact the supplier, they are working on it.

I'll keep you inform asap
CyrilU is offline   Reply With Quote
Old October 22nd, 2010   #5
ericthegeek
Task Group Member
 
Join Date: Aug 2008
Posts: 380
Default

Thanks for the update.

I'd encourage you to attend the ESTA RDM Plugfest in Dallas the weekend of January 22nd. It's a great chance to text your responder with a wide variety of RDM controllers.

I hope the strikes in France aren't effecting you too badly, stay safe!
ericthegeek is offline   Reply With Quote
Old December 20th, 2010   #6
CyrilU
Junior Member
 
Join Date: Oct 2010
Posts: 3
Default

Hello to all,

Finally I have some news about the ghost serial number.

The problem was coming from the sender. I don't know what they did but now with their new software version all is going well.

Thanks for your help

Regards

Cyril
CyrilU is offline   Reply With Quote
Old December 20th, 2010   #7
ericthegeek
Task Group Member
 
Join Date: Aug 2008
Posts: 380
Default

Glad to hear that you got it resolved.
ericthegeek is offline   Reply With Quote
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 05:33 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.